Bộ van điều khiển lưu lượng Bronkhorst IN-FLOW F-230MI
Bộ điều khiển lưu lượng khối Bronkhorst IN-FLOW F-230MI mass flow controller (Industrial Style High-Pressure Mass Flow Controller for Gases) operating pressure / delta-P up to 400 bar để đo lường chính xác và kiểm soát phạm vi lưu lượng từ 0,2…10 mln/phút đến 10…500 mln/phút với áp suất hoạt động lên đến 400 bar và chênh lệch áp suất tối đa 400 bar (ΔP).
IN-FLOW F-230MI mass flow controller bao gồm cảm biến lưu lượng khối nhiệt, van điều khiển chính xác và bo mạch vi xử lý với chuyển đổi tín hiệu và bus trường. Theo giá trị điểm đặt, bộ điều khiển lưu lượng nhanh chóng điều chỉnh lưu lượng mong muốn. Model IN-FLOW có thiết kế chắc chắn (IP65) để sử dụng trong môi trường công nghiệp hoặc thậm chí là khu vực nguy hiểm Zone 2, với tùy chọn phê duyệt ATEX Cat. 3 hoặc FM Class I, Div. 2.
Thông số Bronkhorst IN-FLOW F-230MI mass flow controller
| Measurement / control system | |
|---|---|
| Flow range (intermediate ranges available) | min. 0,2…10 mln/min max. 10…500 mln/min (based on N2) |
| Accuracy (incl. linearity) (based on actual calibration) | ±0,5% Rd plus ±0,1% FS |
| Repeatability | < 0,2 % RD |
| Turndown ratio | 1:50 |
| Multi fluid capability | Storage of max. 8 calibration curves |
| Settling time (in control, typical) | 2 … 4 sec. |
| Control stability | < ± 0,1 % FS |
| Operating temperature | -10 … +70 °C for ATEX cat. 3 and FM Class 1 Div 2 : 0…50°C |
| Temperature sensitivity | zero: < 0,05% FS/°C; span: < 0,05% Rd/°C |
| Pressure sensitivity | 0,1% Rd/bar typical N2; 0,01% Rd/bar typical H2 |
| Leak integrity, outboard | tested < 2 x 10-9 mbar l/s He |
| Attitude sensitivity | max. error at 90° off horizontal 0,2% at 1 bar, typical N2 |
| Warm-up time | 30 min. for optimum accuracy 2 min for accuracy ± 2% FS |
| Mechanical parts | |
|---|---|
| Material (wetted parts) | stainless steel 316L or comparable |
| Pressure rating (PN) | 400 bar abs |
| Min. ΔP | 6 bar dif. |
| Max. ΔP | up to 400 bar dif. |
| Process connections | compression type or face seal couplings |
| Seals | standard: FKM/Viton®; options: EPDM, FFKM/Kalrez® |
| Weight | 3,7 kg |
| Ingress protection | IP65 |
| Electrical properties | |||||
|---|---|---|---|---|---|
| Power supply | +15 … 24 Vdc | ||||
| Max. power consumption |
| ||||
| Analog output | 0…5 (10) Vdc or 0 (4)…20 mA (sourcing output) | ||||
| Digital communication | standard: RS232; options: CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS | ||||
| Electrical connection | |
|---|---|
| Analog/RS232 | 8 DIN (male); |
| PROFIBUS DP | bus: 5-pin M12 (female); power: 8 DIN (male); |
| CANopen® / DeviceNet™ | 5-pin M12 (male); |
| FLOW-BUS/Modbus-RTU/ASCII | 5-pin M12 (male) |
| Modbus TCP / EtherNet/IP / POWERLINK | bus: 2 x 5-pin M12 (female) (in/out); power: 8 DIN (male); |
| EtherCAT®/ PROFINET | bus: 2 x 5-pin M12 (female) (in/out); power: 8 DIN (male); |
| IEC 61010-1 | IEC-61010-1:2010 including national deviations for UL (61010-1:2012) and CSA (C22.2 No. 61010-1-12) |
Bronkhorst® model F-230MI Mass Flow Controllers (MFCs) are suited for accurate measurement and control of flow ranges between 0,2…10 mln/min and 10…500 mln/min with an operating pressure up to 400 bar and max. 400 bar pressure difference (ΔP). The MFC consists of a thermal mass flow sensor, a precise control valve and a microprocessor based pc-board with signal and fieldbus conversion. As a function of a setpoint value, the flow controller swiftly adjusts the desired flow rate. The IN-FLOW model is of rugged design (IP65) for use in industrial environments or even Zone 2 hazardous areas, with optional ATEX Cat. 3 or FM Class I, Div. 2 approval.
IN-FLOW series are equipped with a digital pc-board, offering high accuracy, excellent temperature stability and fast response. The main digital pc-board contains all of the general functions needed for measurement and control. In addition to the standard RS232 output the instruments also offer analog I/O. As an option, an on-board interface can be mounted to provide CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS protocols.
In-Flow F-230MI của Bronkhorst đã từng được đại lý Bronkhorst VN công ty TNHH EURODODO Hotline: 0374008015 email kinhdoanh@eurododo.com cấp hàng ở Việt Nam.




Đánh giá
Chưa có đánh giá nào.