Đồng hồ đo lưu lượng Bronkhorst IN-FLOW F-112AI
Đồng hồ đo lưu lượng khối lượng Bronkhorst IN-FLOW F-112AI mass flow meter (Industrial Style Thermal Mass Flow Meter for Gases) để đo chính xác các dải lưu lượng từ 0,8…40 ln/phút đến 1,4…250 ln/phút với mức áp suất từ chân không đến 100 bar.
IN-FLOW F-112AI mass flow meter bao gồm cảm biến lưu lượng khối lượng nhiệt và bo mạch vi xử lý với chuyển đổi tín hiệu và bus trường và bộ điều khiển PID để điều khiển lưu lượng khối lượng tùy chọn bằng van điều khiển gắn riêng. Model IN-FLOW có thiết kế chắc chắn (IP65) để sử dụng trong môi trường công nghiệp hoặc thậm chí là khu vực nguy hiểm Zone 2, với tùy chọn ATEX Cat. 3 hoặc FM Class I, Div. 2.
Thông số Bronkhorst IN-FLOW F-112AI mass flow meter
| Measurement / control system | |
|---|---|
| Flow range (intermediate ranges available) | min. 0,8…40 ln/min max. 1,4…250 ln/min (based on N2) |
| Accuracy (incl. linearity) (based on actual calibration) | ±0,5% Rd plus ±0,1% FS |
| Repeatability | < 0,2 % RD |
| Turndown ratio | up to 1:187,5 (1:50 in analog mode) |
| Multi fluid capability | storage of max. 8 calibration curves; optional Multi Gas / Multi Range functionality up to 10 bar abs |
| Response time (sensor) | typical: 0,5 sec. |
| Operating temperature | -10 … +70 °C for ATEX cat. 3 and FM Class 1 Div 2 : 0…50°C |
| Temperature sensitivity | zero: < 0,05% FS/°C; span: < 0,05% Rd/°C |
| Pressure sensitivity | 0,1% Rd/bar typical N2; 0,01% Rd/bar typical H2 |
| Leak integrity, outboard | tested < 2 x 10-9 mbar l/s He |
| Attitude sensitivity | max. error at 90° off horizontal 0,2% FS at 1 bar, typical N2 |
| Warm-up time | 30 min. for optimum accuracy 2 min for accuracy ± 2% FS |
| Mechanical parts | |
|---|---|
| Material (wetted parts) | stainless steel 316L or comparable |
| Pressure rating (PN) | 100 bar abs |
| Process connections | compression type or face seal couplings |
| Seals | standard: FKM/Viton®; options: EPDM, FFKM/Kalrez®, FDA and USP Class VI approved compounds |
| Weight | 1,8 kg |
| Ingress protection | IP65 |
| Electrical properties | |||||
|---|---|---|---|---|---|
| Power supply | +15 … 24 Vdc | ||||
| Max. power consumption meter |
| ||||
| Max. Power consumption controller |
| ||||
| Analog output | 0…5 (10) Vdc or 0 (4)…20 mA (sourcing output) | ||||
| Digital communication | standard: RS232; options: CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS | ||||
| Electrical connection | |
|---|---|
| Analog/RS232 | 8 DIN (male); |
| PROFIBUS DP | bus: 5-pin M12 (female); power: 8 DIN (male); |
| CANopen® / DeviceNet™ | 5-pin M12 (male); |
| FLOW-BUS/Modbus-RTU/ASCII | 5-pin M12 (male) |
| Modbus TCP / EtherNet/IP / POWERLINK | bus: 2 x 5-pin M12 (female) (in/out); power: 8 DIN (male); |
| EtherCAT®/ PROFINET | bus: 2 x 5-pin M12 (female) (in/out); power: 8 DIN (male); |
| IEC 61010-1 | IEC-61010-1:2010 including national deviations for UL (61010-1:2012) and CSA (C22.2 No. 61010-1-12) |
Bronkhorst® model F-112AI Mass Flow Meters (MFMs) are suited for precise measurement of flow ranges between 0,8…40 ln/min and 1,4…250 ln/min with pressure rating between vacuum and 100 bar. The MFM consists of a thermal mass flow sensor and a microprocessor based pc-board with signal and fieldbus conversion and a PID controller for optional mass flow control by means of a separately mounted control valve. The IN-FLOW model is of rugged design (IP65) for use in industrial environments or even Zone 2 hazardous areas, with optional ATEX Cat. 3 or FM Class I, Div. 2 approval.
IN-FLOW series are equipped with a digital pc-board, offering high accuracy, excellent temperature stability and fast response. The main digital pc-board contains all of the general functions needed for measurement and control. In addition to the standard RS232 output the instruments also offer analog I/O. As an option, an on-board interface can be mounted to provide CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS protocols. The IN-FLOW model features optional Multi Gas / Multi Range functionality, providing (OEM-) customers with optimal flexibility and process efficiency.
In-Flow F-112AI của Bronkhorst đã từng được đại lý Bronkhorst VN công ty TNHH EURODODO Hotline: 0374008015 email kinhdoanh@eurododo.com cấp hàng ở Việt Nam.




Đánh giá
Chưa có đánh giá nào.